Oil Rigs Now presents a platform where buyers can connect directly with sellers of various oilfield equipment without intermediaries.
Why Choose Used Oilfield Equipment?
Used equipment can lower the upfront cost of a program. Buyers are encouraged to have an independent inspector review the rig before purchase.
Types of Equipment Available
Listing categories on the site include:
- Land drilling rigs
- Mobile workover rigs
- Offshore rigs
Each piece of equipment is listed by its seller.
How to Navigate the Listings
Simply visit the Equipment Listings page and open each unit's page for its spec sheet.
Contact for More Information
For inquiries regarding specific listings, potential buyers can contact the seller directly. Pricing on a specific listing comes from Bob Neundorf at [email protected] or by phone at 832-563-0880.
Rigs for South Texas Work Listed on Oil Rigs Now
San Antonio sits just north of the Eagle Ford shale, where operators drill horizontal wells from pads, and near the Austin Chalk. Several listings are in South Texas, which shortens inspection trips for buyers based in San Antonio:
- IDM-1500 Rig 5 – 1500 HP SCR Drilling Rig: listed in Corpus Christi. A 2007 1500 HP SCR rig with an IDM 136 ft telescoping mast, 750,000 lb hook load, three Cummins KTA50DR engines and two Continental EMSCO FB-1600 mud pumps.
- Continental EMSCO 1500HP Rig 2: listed in Corpus Christi. The sheet lists a Continental EMSCO C-1 drawworks, a 136 ft IRI mast, 750,000 lb hook load, a Canrig 350-ton top drive and twin FB-1300 mud pumps.
- IDECO E-1200 1200HP Walking Rig 1: a 2003 IDECO E-1200 walking rig listed in Corpus Christi.
- Drillmec 2300 HP Land Rig: a 2013 Drillmec 2300 HP AC land rig listed in Texas.
These figures are the sellers' own spec sheets as listed. Confirm each one against the equipment and its paperwork during an independent inspection.
Eagle Ford wells are mostly drilled by 1200 to 1500 HP rigs with top drives and, increasingly, walking systems, so the Corpus Christi units above line up with what South Texas operators typically run.
Comparing the South Texas Listings
The two Corpus Christi 1500 HP rigs share a hook load rating of 750,000 lb and 136 ft masts, but they differ in drawworks and pumps. The IDM-1500 sheet lists two Continental EMSCO FB-1600 pumps and Cummins KTA50DR engines. The Continental EMSCO Rig 2 sheet lists a C-1 drawworks, a Canrig 350-ton top drive and twin FB-1300 pumps. For long Eagle Ford laterals, pump horsepower and pressure rating often decide between rigs of the same size.
Frequently Asked Questions
What is the process for purchasing used oilfield equipment?
Buyers should explore the listings, contact the seller directly, and ask about inspection and logistics when they inquire.
What condition terms apply to listed equipment?
Equipment is sold as-is per the seller's terms. Ask about inspection and logistics when you inquire.
How do I find the right equipment for my needs?
Start from the listings page and compare each unit's spec sheet by type, horsepower and location.
What should I ask about a rig's last work history?
Ask where and for how long it last drilled, how long it has been stacked, and how it was stored. A rig stacked outdoors on the Gulf Coast needs a closer look at corrosion on the mast, substructure and electrical connections.
How many loads does a rig move take in South Texas?
It varies by rig. A super single moves on far fewer trailers than a triple. Ask each seller for the load count and the heaviest single load, then check both against state permit limits for your route.
Should I inspect a rig before or after making an offer?
Most buyers make an offer subject to inspection, then commission an independent inspection of the mast, substructure, drawworks, top drive, pumps and BOP. Ask the seller about inspection access and logistics when you inquire.